![]() ![]() Use a collar ring to hide the seam between the elbow and the rail if desired. Step 1: Cut the railingĬut the railing to the proper length based on the location of the elbows and other components being used. Step 6: Attach the wall returnįinally, attach the wall return to the post as previously described and use end caps where required for a finished appearance.Įlbows are used to change the direction of your handrail on a staircase or ramp. Remove the metal spacer screw using a #2 square-head screwdriver and push the handrail return further over the internal connector until it fits in the collar (if you used one) or fits tightly against the elbow. Slide the opposite end of the handrail return onto the internal connector until it's touching the metal spacer screw. The wall return is designed to fit tightly into the rail, so the location of the attachment is critical. ![]() Make sure the wall return is at the proper angle of alignment to the post. Next, attach the wall return to the lower end of the handrail return (the longer side). Once everything is lined up, slide the internal connector into the appropriate elbow until the metal spacer screw is touching either end of the elbow or the collar, if you used one. This means checking that the wall mount on the post lines up with the location of the elbow on the rail. Step 2: Align the componentsīefore you attach anything, make sure all the components are aligned properly. Slide the collar ring over the rail before inserting it into the other component. You'll also want to use a collar ring if you want to hide the seam between the handrail return and the rail or elbow. Step 1: Cut the railingįirst, make sure you have the right railing length for your handrail return. Handrails ensure your railing extends beyond the top and bottom of a set of stairs or a ramp, as required by ADA guidelines. Step 5: Attach the railįinally, attach the connected rail to the wall mount using the provided hardware and finish by attaching the end cap to the rail for a safe, professional finish. To help with an angled attachment, place one screw into the bottom hole of the bracket and pivot the wall mount to the required position. Make sure each wall mount is at the proper angle of alignment to the angle of the rail. Step 4: Attach wall mountsĪttach wall mounts as needed to posts using the provided hardware, keeping in mind that a wall mount must be used at each rail-to-rail seam connection. With the screw removed, push the second rail further over the internal connector until it fits in the collar or tightly against the opposite rail. Next, remove the spacer screw using a #2 square-head screwdriver. Next, slide the second rail over the opposite end of the internal connector until it is also touching the metal spacer screw. Slide the internal connector into the rail end until the metal spacer screw touches either the end of the handrail or the collar if you’re using one. Make sure to slide the collar over one rail before connecting. To hide the seam where the two pieces of handrail will meet, you can use a collar ring. Step 1: Cut the railingĬut railings to size if two or more full-lengths are not required. Posts must be installed at a maximum of 6 feet on center when using rail-to-rail connections. Below are some examples and the requirements as stated in the ICC/ANSI A117.1 Accessible and Usuable Buildings and Facilities.Rail-to-rail straight connections are used for longer spans of handrails. However, the requirements are rather straight forward. Since it is not referenced in the ADA Standards or in the Texas Accessibility Standards, as a Registered Accessibility Specialist in the state of Texas, I cannot review it during the Plan Review process or during the required Inspection. Also, it is very helpful for people with disabilities and it is not an expensive addition to the overall budget of the project. Some architects/designers will specify the vertical grab bar on their drawings just to ensure that it is not a comment from the city. One of the the most common one is the vertical grab bar. The IBC makes reference to the ICC/ANSI A117.1 and some cities will use it while performing their plan review prior to issuing a permit for construction. While it does follow the Department of Justice's 2010 ADA Standards for Accessible Design, there are some differences. The ICC is the same organization that puts out the International Building Code or IBC. It is another accessibility code standard. The vertical grab bar is only specified in the ICC/ANSI A117.1 Accessible and Usable Buildings and Facilities. However, you will often see them while in a toilet room or in the accessible stall. The ADA Standards require horizontal grab bars on the rear wall and side wall of the water closet, but it does not specify a vertical grab bar. Grab bars are required in accessible toilet rooms. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |